Texas Instruments X-Loader 1.4.2 (Feb 19 2009 - 12:01:24) Reading boot sector Error: reading boot sector Loading u-boot.bin from nand U-Boot 2009.01-dirty (Feb 19 2009 - 12:22:31) I2C: ready OMAP3530-GP rev 2, CPU-OPP2 L3-165MHz OMAP3 Beagle board + LPDDR/NAND DRAM: 256 MB NAND: 256 MiB *** Warning - bad CRC or NAND, using default environment MUSB: using high speed In: serial usbtty Out: serial usbtty Err: serial usbtty Board revision C Serial #34b2000300000000040323090f01c011 Hit any key to stop autoboot: 10  9  8  7  6  5  4  3  2  1  0 reading boot.scr ** Unable to read "boot.scr" from mmc 0:1 ** reading uImage.bin 3271552 bytes read reading ramdisk.gz ** Unable to read "ramdisk.gz" from mmc 0:1 ** Booting from mmc ... ## Booting kernel from Legacy Image at 80200000 ... Image Name: Linux-2.6.31.6 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3271488 Bytes = 3.1 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux.................................................................................................................................................................................................................... done, booting the kernel. [ 0.000000] Linux version 2.6.31.6 (root@beaglecnc) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) #1 PREEMPT Tue Nov 17 18:21:25 EST 2009 [ 0.000000] CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c53c7f [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache [ 0.000000] Machine: OMAP3 Beagle Board [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] OMAP3430 ES3.0 [ 0.000000] SRAM: Mapped pa 0x40200000 to va 0xe3000000 size: 0x100000 [ 0.000000] Reserving 14680064 bytes SDRAM for VRAM [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS2,115200n8 root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait [ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 128MB 128MB = 256MB total [ 0.000000] Memory: 238336KB available (6000K code, 669K data, 200K init, 0K highmem) [ 0.000000] NR_IRQS:402 [ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz [ 0.000000] Reprogramming SDRC clock to 332000000 Hz [ 0.000000] GPMC revision 5.0 [ 0.000000] IRQ: Found an INTC at 0xd8200000 (revision 4.0) with 96 interrupts [ 0.000000] Total of 96 interrupts on 1 active controller [ 0.000000] OMAP34xx GPIO hardware version 2.5 [ 0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Calibrating delay loop... 492.62 BogoMIPS (lpj=1925120) [ 0.000000] Mount-cache hash table entries: 512 [ 0.000000] CPU: Testing write buffer coherency: ok [ 0.000000] regulator: core version 0.5 [ 0.000000] NET: Registered protocol family 16 [ 0.000000] Found NAND on CS0 [ 0.000000] Registering NAND on CS0 [ 0.000000] OMAP DMA hardware revision 4.0 [ 0.000000] bio: create slab at 0 [ 0.000000] i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz [ 0.000000] twl4030: PIH (irq 7) chaining IRQs 368..375 [ 0.000000] twl4030: power (irq 373) chaining IRQs 376..383 [ 0.000000] twl4030: gpio (irq 368) chaining IRQs 384..401 [ 0.000000] regulator: VMMC1: 1850 <--> 3150 mV normal standby [ 0.000000] regulator: VDAC: 1800 mV normal standby [ 0.000000] regulator: VUSB1V5: 1500 mV normal standby [ 0.000000] regulator: VUSB1V8: 1800 mV normal standby [ 0.000000] regulator: VUSB3V1: 3100 mV normal standby [ 0.000000] regulator: VPLL2: 1800 mV normal standby [ 0.000000] regulator: VSIM: 1800 <--> 3000 mV normal standby [ 0.000000] i2c_omap i2c_omap.3: bus 3 rev3.12 at 100 kHz [ 0.000000] SCSI subsystem initialized [ 0.000000] twl4030_usb twl4030_usb: Initialized TWL4030 USB module [ 0.000000] usbcore: registered new interface driver usbfs [ 0.000000] usbcore: registered new interface driver hub [ 0.000000] usbcore: registered new device driver usb [ 0.000000] Bluetooth: Core ver 2.15 [ 0.000000] NET: Registered protocol family 31 [ 0.000000] Bluetooth: HCI device and connection manager initialized [ 0.000000] Bluetooth: HCI socket layer initialized [ 0.000000] cfg80211: Using static regulatory domain info [ 0.000000] cfg80211: Regulatory domain: US [ 0.000000] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 0.000000] (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm) [ 0.000000] (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 0.000000] (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 0.000000] (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 0.000000] (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 0.000000] (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm) [ 0.000000] cfg80211: Calling CRDA for country: US [ 24.542694] musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0 [ 24.545654] musb_hdrc: USB OTG mode controller at d80ab000 using DMA, IRQ 92 [ 24.546997] NET: Registered protocol family 2 [ 24.547271] IP route cache hash table entries: 2048 (order: 1, 8192 bytes) [ 24.547912] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 24.548187] TCP bind hash table entries: 8192 (order: 3, 32768 bytes) [ 24.548309] TCP: Hash tables configured (established 8192 bind 8192) [ 24.548339] TCP reno registered [ 24.548614] NET: Registered protocol family 1 [ 24.553314] VFS: Disk quotas dquot_6.5.2 [ 24.553436] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 24.554107] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 24.554901] JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 24.555877] msgmni has been set to 465 [ 24.561889] alg: No test for stdrng (krng) [ 24.562011] io scheduler noop registered [ 24.562042] io scheduler anticipatory registered [ 24.562042] io scheduler deadline registered [ 24.562286] io scheduler cfq registered (default) [ 24.619232] OMAP DSS rev 2.0 [ 24.619323] OMAP DISPC rev 3.0 [ 24.619384] OMAP VENC rev 2 [ 24.619934] OMAP DSI rev 1.0 [ 24.975311] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 24.997924] serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654 [ 25.018798] serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654 [ 25.039581] serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654 [ 25.039642] console [ttyS2] enabled [ 25.552490] brd: module loaded [ 25.563598] loop: module loaded [ 25.567321] i2c /dev entries driver [ 25.574584] usbcore: registered new interface driver catc [ 25.580017] catc: v2.8:CATC EL1210A NetMate USB Ethernet driver [ 25.587066] usbcore: registered new interface driver kaweth [ 25.592773] pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver [ 25.600708] usbcore: registered new interface driver pegasus [ 25.606475] rtl8150: v0.6.2 (2004/08/27):rtl8150 based usb-ethernet driver [ 25.613800] usbcore: registered new interface driver rtl8150 [ 25.619842] usbcore: registered new interface driver asix [ 25.625549] usbcore: registered new interface driver cdc_ether [ 25.631774] usbcore: registered new interface driver dm9601 [ 25.637756] usbcore: registered new interface driver smsc95xx [ 25.643890] usbcore: registered new interface driver gl620a [ 25.649780] usbcore: registered new interface driver net1080 [ 25.655822] usbcore: registered new interface driver plusb [ 25.661712] usbcore: registered new interface driver rndis_host [ 25.667999] usbcore: registered new interface driver cdc_subset [ 25.674316] usbcore: registered new interface driver zaurus [ 25.680267] Broadcom 43xx driver loaded [ Features: L, Firmware-ID: FW13 ] [ 25.687683] usbcore: registered new interface driver zd1211rw [ 25.693878] usbcore: registered new interface driver rtl8187 [ 25.699920] usbcore: registered new interface driver rndis_wlan [ 25.706268] usbcore: registered new interface driver zd1201 [ 25.712249] usbcore: registered new interface driver usb8xxx [ 25.718322] usbcore: registered new interface driver rt2500usb [ 25.724578] usbcore: registered new interface driver rt73usb [ 25.730651] usbcore: registered new interface driver rt2800usb [ 25.736907] usbcore: registered new interface driver p54usb [ 25.742828] usbcore: registered new interface driver ar9170usb [ 25.749298] omap2-nand driver initializing [ 25.753784] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB 1,8V 16-bit) [ 25.762908] cmdlinepart partition parsing not available [ 25.768218] Creating 5 MTD partitions on "omap2-nand": [ 25.773406] 0x000000000000-0x000000080000 : "X-Loader" [ 25.780822] 0x000000080000-0x000000260000 : "U-Boot" [ 25.788146] 0x000000260000-0x000000280000 : "U-Boot Env" [ 25.795074] 0x000000280000-0x000000680000 : "Kernel" [ 25.803192] 0x000000680000-0x000010000000 : "File System" [ 25.917144] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 25.924163] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller [ 25.930480] ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1 [ 25.938385] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800 [ 25.955108] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00 [ 25.961791] usb usb1: configuration #1 chosen from 1 choice [ 25.967987] hub 1-0:1.0: USB hub found [ 25.971893] hub 1-0:1.0: 3 ports detected [ 25.977294] Initializing USB Mass Storage driver... [ 25.982696] usbcore: registered new interface driver usb-storage [ 25.988830] USB Mass Storage support registered. [ 25.993530] g_ether gadget: using random self ethernet address [ 25.999481] g_ether gadget: using random host ethernet address [ 26.006256] usb0: MAC 0e:0c:b9:f6:74:2c [ 26.010162] usb0: HOST MAC 66:7c:67:47:7f:b4 [ 26.014526] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008 [ 26.021301] g_ether gadget: g_ether ready [ 26.025329] musb_hdrc musb_hdrc: MUSB HDRC host driver [ 26.031158] musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 2 [ 26.039306] usb usb2: configuration #1 chosen from 1 choice [ 26.045501] hub 2-0:1.0: USB hub found [ 26.049407] hub 2-0:1.0: 1 port detected [ 26.054870] mice: PS/2 mouse device common for all mice [ 26.060974] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 26.071380] OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec [ 26.077972] Bluetooth: HCI UART driver ver 2.2 [ 26.082519] Bluetooth: HCI H4 protocol initialized [ 26.087341] Bluetooth: HCI BCSP protocol initialized [ 26.092407] Bluetooth: HCILL protocol initialized [ 26.097198] Bluetooth: Broadcom Blutonium firmware driver ver 1.2 [ 26.103729] usbcore: registered new interface driver bcm203x [ 26.109436] Bluetooth: Digianswer Bluetooth USB driver ver 0.10 [ 26.115844] usbcore: registered new interface driver bpa10x [ 26.121551] Bluetooth: BlueFRITZ! USB driver ver 1.2 [ 26.126861] usbcore: registered new interface driver bfusb [ 26.132446] Bluetooth: Generic Bluetooth USB driver ver 0.5 [ 26.138427] usbcore: registered new interface driver btusb [ 26.144012] Bluetooth: Generic Bluetooth SDIO driver ver 0.1 [ 26.151611] mmci-omap-hs mmci-omap-hs.0: Failed to get debounce clock [ 26.269531] Registered led device: beagleboard::usr0 [ 26.274871] Registered led device: beagleboard::usr1 [ 26.280731] Registered led device: beagleboard::pmu_stat [ 26.292968] usbcore: registered new interface driver usbhid [ 26.298614] usbhid: v2.6:USB HID core driver [ 26.303283] usb 1-2: new high speed USB device using ehci-omap and address 2 [ 26.311981] Advanced Linux Sound Architecture Driver Version 1.0.20. [ 26.319396] usbcore: registered new interface driver snd-usb-audio [ 26.326477] No device for DAI twl4030 [ 26.330230] No device for DAI twl4030 Voice [ 26.334442] No device for DAI omap-mcbsp-dai-0 [ 26.338989] No device for DAI omap-mcbsp-dai-1 [ 26.343475] No device for DAI omap-mcbsp-dai-2 [ 26.347961] No device for DAI omap-mcbsp-dai-3 [ 26.352447] No device for DAI omap-mcbsp-dai-4 [ 26.356964] Not OMAP3 EVM! [ 26.359680] OMAP3 Beagle SoC init [ 26.363525] TWL4030 Audio Codec init [ 26.368774] asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok [ 26.467376] ALSA device list: [ 26.470367] #0: omap3beagle (twl4030) [ 26.474700] usb 1-2: configuration #1 chosen from 1 choice [ 26.481292] hub 1-2:1.0: USB hub found [ 26.485290] hub 1-2:1.0: 4 ports detected [ 26.489837] oprofile: using arm/armv7 [ 26.493835] TCP cubic registered [ 26.497161] NET: Registered protocol family 17 [ 26.501708] NET: Registered protocol family 15 [ 26.506286] Bluetooth: L2CAP ver 2.13 [ 26.510009] Bluetooth: L2CAP socket layer initialized [ 26.515136] Bluetooth: SCO (Voice Link) ver 0.6 [ 26.519714] Bluetooth: SCO socket layer initialized [ 26.524932] Bluetooth: RFCOMM TTY layer initialized [ 26.529937] Bluetooth: RFCOMM socket layer initialized [ 26.535186] Bluetooth: RFCOMM ver 1.11 [ 26.539001] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 26.544372] Bluetooth: BNEP filters: protocol multicast [ 26.549652] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 26.557678] RPC: Registered udp transport module. [ 26.562438] RPC: Registered tcp transport module. [ 26.567321] lib80211: common routines for IEEE802.11 drivers [ 26.573150] ThumbEE CPU extension supported. [ 26.577453] Power Management for TI OMAP3. [ 26.592590] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1 [ 26.602661] registered taskstats version 1 [ 26.626495] Console: switching to colour frame buffer device 80x30 [ 26.651458] regulator_init_complete: incomplete constraints, leaving VDAC on [ 26.659179] Waiting for root device /dev/mmcblk0p2... [ 26.689605] mmc0: new high speed SDHC card at address e624 [ 26.695892] mmcblk0: mmc0:e624 SU04G 3.69 GiB [ 26.700775] mmcblk0: p1 p2 p3 < p5 > [ 26.846313] usb 1-2.1: new high speed USB device using ehci-omap and address 3 [ 26.976745] usb 1-2.1: configuration #1 chosen from 1 choice [ 36.507598] kjournald starting. Commit interval 5 seconds [ 36.516296] EXT3 FS on mmcblk0p2, internal journal [ 36.521179] EXT3-fs: recovery complete. [ 36.527832] EXT3-fs: mounted filesystem with writeback data mode. [ 36.534057] VFS: Mounted root (ext3 filesystem) on device 179:2. [ 36.540283] Freeing init memory: 200K INIT: version 2.86 booting Starting the hotplug events dispatcher: udevd. Synthesizing the initial hotplug events...done. Waiting for /dev to be fully populated...[ 44.232513] twl4030_rtc twl4030_rtc: rtc core: registered twl4030_rtc as rtc0 [ 44.914459] usb 1-2.1: applying rev.C fixup [ 44.958465] usb 1-2.1: applying rev.C fixup [ 45.007110] eth0: register 'MOSCHIP usb-ethernet driver' at usb-ehci-omap.0-2.1, MOSCHIP 7830/7730 usb-NET adapter, 00:60:6e:11:01:dc [ 45.097869] usbcore: registered new interface driver MOSCHIP usb-ethernet driver [ 46.067840] uncorrectable error : [ 46.071105] end_request: I/O error, dev mtdblock0, sector 0 [ 46.076904] Buffer I/O error on device mtdblock0, logical block 0 [ 46.083374] uncorrectable error : [ 46.086608] end_request: I/O error, dev mtdblock0, sector 8 [ 46.092407] Buffer I/O error on device mtdblock0, logical block 1 [ 46.098968] uncorrectable error : [ 46.102233] end_request: I/O error, dev mtdblock0, sector 16 [ 46.108123] Buffer I/O error on device mtdblock0, logical block 2 [ 46.114501] uncorrectable error : [ 46.117767] end_request: I/O error, dev mtdblock0, sector 24 [ 46.123657] Buffer I/O error on device mtdblock0, logical block 3 [ 46.150756] uncorrectable error : [ 46.154022] end_request: I/O error, dev mtdblock0, sector 0 [ 46.159851] Buffer I/O error on device mtdblock0, logical block 0 [ 46.237030] end_request: I/O error, dev mtdblock1, sector 0 [ 46.242675] Buffer I/O error on device mtdblock1, logical block 0 [ 46.308074] end_request: I/O error, dev mtdblock1, sector 0 [ 46.313720] Buffer I/O error on device mtdblock1, logical block 0 [ 47.159027] udev: renamed network interface eth0 to eth1 done. Setting the system clock. Activating swap...[ 49.024505] Adding 49360k swap on /dev/mmcblk0p5. Priority:-1 extents:1 across:49360k SS done. Checking root file system...fsck 1.41.3 (12-Oct-2008) /dev/mmcblk0p2: clean, 122607/474208 files, 705868/946680 blocks done. [ 53.752563] EXT3 FS on mmcblk0p2, internal journal Setting the system clock. Cleaning up ifupdown.... Loading kernel modules...done. Checking file systems...fsck 1.41.3 (12-Oct-2008) done. Setting kernel variables (/etc/sysctl.conf)...done. Mounting local filesystems...done. Activating swapfile swap...done. Setting up networking.... Configuring network interfaces...done. Starting portmap daemon.... Starting NFS common utilities: statd. Setting console screen modes and fonts. Setting up ALSA...done. [ 59.669952] NET: Registered protocol family 10 INIT: Entering runlevel: 2 Loading cpufreq kernel modules...done (none). Starting enhanced syslogd: rsyslogd. Starting system message bus: dbus. Starting OpenBSD Secure Shell server: sshd. CPUFreq Utilities: Setting ondemand CPUFreq governor...disabled, governor not available...done. Starting Common Unix Printing System: cupsd. Starting kerneloops: Starting NFS common utilities: statd. Not starting internet superserver: no services enabled. Starting Hardware abstraction layer: hald. Starting network connection manager: NetworkManager[ 68.539245] ADDRCONF(NETDEV_UP): usb0: link is not ready . Starting network events dispatcher: NetworkManagerDispatcher. Starting System Tools Backends: system-tools-backends. Starting anac(h)ronistic cron: anacron. Starting deferred execution scheduler: atd. Starting periodic command scheduler: crond. Enabling additional executable binary formats: binfmt-support. Starting Signal Switcher(2020) server: switcher. Debian GNU/Linux 5.0 beaglecnc ttyS2 beaglecnc login: